Keo dán Nhựa tổng hợp 3M 1099

Keo dán Nhựa tổng hợp 3M 1099

SPECS

ITEM	Scotch-Grip(TM) Plastic Adhesive
TYPE	Best for Nitrile, Medium Viscosity, Fast Dry
COLOR	Tan
SIZE	5-oz. Tube
TEMP. RANGE (F)	-40 to 180
APPLICATION TIME	Up to 40 Min.
FUNCTIONAL CURE	24 Hrs.
FULL CURE	24 hr.
WORK LIFE	40 min.
SHEAR STRENGTH (PSI)	1306
APPLICATION	Bonds Vinyl Extrusions and Sheeting, Fabrics, Foams and Many Plastics
GREEN ENVIRONMENTAL ATTRIBUTE	VOC Levels Meet SCAQMD Requirements
UNSPSC	31201601
WEIGHT	0.300000
SKUS	3XH42

DESCRIPTION

Plastic Adhesive, Size 5 Ounces Tube, Item Scotch Grip, Application Time 40 Minutes, Temperature Range -40 to 250 Degrees Fahrenheit, Tan Fast Drying, Resists Weathering

Restrictions

• Hazardous Material

 

Epoxy, Acrylic, and Plastic Adhesives

• 1099
• See table Type column for more information regarding specific adhesives.
• Fast-drying. Resists weathering, water, oil, plasticizer migrations, aliphatic fuels. Bonds vinyl extrusions and sheeting, fabrics, foams, many plastics.
• Plastic Adhesives

 

3M™ SCOTCH-WELD™ 1099 NITRILE HIGH PERFORMANCE PLASTIC ADHESIVE - MIL-A-13883

Plastics don't always adhere like you want them to, especially when you're in a rush. We think it's because of Murphy's Law of Aviation: "Anything you fix quickly like a pro will inevitably break and make you feel like an amateur." Luckily, 3M™ 1099 Scotch-Weld™ Nitrile High Performance Plastic Adhesive isn't bound by such a law.

3M™ Scotch-Weld™ 1099 is a fast-drying, strong and liquid-resistant adhesive that works well in dozens of aviation applications, especially as it pertains to plastics. It doesn't stop there, though. It can bond fabrics, foams and other surfaces as well. Bonding, adhering, gluing, joining, attaching-it's all there.

Stick with this item and you will possess a flexible but strong adhesive that resists weathering, water, fuels, oils and plasticizers. Thus, it works well on the inside as well as on the outside of any aircraft.

Whether you need five ounces, a quart or a gallon, we can provide you with the 3M™ Scotch-Weld™ 1099 High Performance Plastic Adhesive you need to get the job done.

Additional information, including features and directions for use, can be found below.

Directions for Use

Directions For Use

1. Surface Preparation: Remove all dust, dirt, oil, grease, wax, loose paint, etc. Wiping with methyl ethyl ketone (MEK)* or 3M™ Citrus Base Cleaner* will aid in preparing the surface for bonding.
2. Application Temperature: For best results, the temperature of the adhesive and surfaces should be at least 65°F (18°C).
3. Application: Stir well before using.
   Porous Surface(s): Brush, flow or spray a thin, even coat of adhesive to one or both surfaces. Coating both surfaces is preferred since it gives greater strength and permits longer open time before bonding. Very absorbent materials may require more than one coat. Bond while adhesive is still wet or aggressively tacky. Join surfaces with firm pressure.
   Non-Porous Surface(s): Brush, flow or spray a thin, even coat of adhesive to both surfaces. Allow adhesive to dry until tacky. Join surfaces with firm pressure.
4. Drying Time: Drying time depends on temperature, humidity, air movement, and porosity of the materials bonded. Greater immediate strength may be obtained by heat or solvent reactivation. See Reactivation below.
5. Reactivation: To solvent reactivate, coat both surfaces with adhesive. Allow to dry tack-free. Lightly wipe one surface with a solvent such as methyl ethyl ketone (MEK).* Complete bond within 30 seconds. To heat reactivate, coat both surfaces with adhesive. Allow adhesive to dry completely. Reactivate by heating one or both surfaces to a minimum of 180°F (82°C). Assemble immediately (while hot), using firm pressure to ensure contact.
6. Curing: 3M™ Scotch-Weld™ Nitrile High Performance Plastic Adhesive 1099 and 1099-L may be heat cured to obtain superior properties. Cure assembled parts at time and temperature listed using 100 psi pressure on the bond line.
   
   

   Temperature of Bondline Time for Minimum Cure 200°F (93°C) 120 Minutes 240°F (116°C) 40 Minutes 280°F (138°C) 12 Minutes 320°F (160°C) 8 Minutes 360°F (182°C) 5 minutes 400°F (204°C) 2 Minutes

   
   
7. Cleanup: Excess adhesive may be removed with methyl ethyl ketone (MEK)* or acetone,* preferably while adhesive is still wet.
   *Note: When using solvents, extinguish all ignition sources, including pilot lights, and follow manufacturer’s precautions and directions for use.

Features

• Medium viscosity grade for most brush or flow applications
• Fast drying
• Provides strong, flexible bonds
• Resists weathering, water, fuels, oil and plasticizers
• Bonds vinyl extrusions and sheeting (May stain light colored vinyls)
• Also bonds fabrics, foams and many plastics (Not recommended for polyolefin plastic bonding)
• May be heat cured to obtain superior physical properties